You are viewing this page with JavaScript disabled!
Please enable JavaScript or contact your system administrator for the best viewing experience!

IMPORTANT NOTICE!

The interactive parts of this page (Amounts, Checkout Button, etc.) do not work with disabled JavaScript!
You will not be able to complete a purchase with disabled JavaScript!
Please enable JavaScript or contact your system administrator in order to resolve this issue!
Alternatively you can email us at info@neonious.com to place your order.
Buy in..
USD
EUR
Product
Enter amount:
Cost
low.js Professional
If you have a generic ESP32-WROVER based board with a minimum of 16 MB Flash, you can flash low.js Professional known from the neonious one. For more information on this software, please go to the neonious one Product Page.
  • Well done on-board webbrowser-based IDE + debugger for rapid prototyping
  • Graphical package manager for npm
  • Support for native C/C++ modules via low native API
  • Over-the-air updates of low.js, no need to connect board to PC
After purchase, you will receive a key. To flash, call lowsync flash --init --port=theport --pro --pro-key=thekey
The key is only valid for the first device you use it on.
Cost: 
15.00 USD
For volume licenses, please contact us and ask for a quote.
neonious one + low.js Professional
Microcontroller board optimized for low.js, with many features not possible with generic ESP32-WROVER hardware, such as:
  • Truely asynchronous Flash writes, as file system is on additional Flash chips (ESP32-WROVER Flash writes always stop the system, by design)
  • 4 MB of Flash for file system / user program, additional Flash for low.js + IDE
  • 10/100 MBit Ethernet
  • Well done on-board webbrowser-based IDE + debugger for rapid prototyping
  • Graphical package manager for npm
  • Support for native C/C++ modules via low native API
  • Over-the-air updates of low.js, no need to connect board to PC
  • Clean pin layout with every pin actually usable, far more usable pins than plain ESP32-WROVER has
  • Accurate ADC provided LPC coprocessor (ESP32 ADC is non-linear)
For more information, please go to the neonious one Product Page.
1x
40.00 USD
3x
34.00 USD (15 % off)
10x
26.00 USD (35 % off)
Over 300 in stock, shipment within 5 working days from Germany, EU
TTGO T8 V1.8 Board

Microcontroller board with ESP32-WROVER, 4 MB Flash, 4 MB RAM, UART 2 USB, Battery Port and microSD Port. All ports available via pins.

For the pin out diagram of this board, please click here.

Cost: 
14.00 USD
Over 50 in stock, shipment within 5 working days from Germany, EU
TTGO T7 V1.7 Tiny Board

ESP32-WROVER with 4 MB Flash and 4 MB RAM soldered on tiny breakout board. Also includes USB 2 UART and battery connector! All ports are available via pins.

For more information, please look here: TTGO T7 Demo Repository.

Cost: 
17.50 USD
Over 15 in stock, shipment within 5 working days from Germany, EU
ESP32-Ethernet-Kit Board with POE

Microcontroller board with ESP32-WROVER, 4 MB Flash, 4 MB RAM, UART 2 USB, 10/100 MBit Ethernet and Power-over-Ethernet. The Ethernet port is fully supported by low.js. Version 1.1.

For more information, please go to the ESP32-Ethernet-Kit Product Page.
Cost: 
65.00 USD
3 in stock, shipment within 5 working days from Germany, EU
neonious C/C++ Hacking Kit
Includes everything to program the neonious one in bare metal C/C++ without low.js, including FTDI USB-to-TTL board, access to template project based on ESP-IDF (for ESP32) and LPCOpen (for LPC822) and neonious one device schemantics. Also allows you to reflash the low.js environment. For more information, please go to the product announcement in our blog.
Cost: 
6.00 USD
Over 20 in stock, shipment within 5 working days from Germany, EU
ESP32-WROVER 4 MB
Module with ESP32 microcontroller, 4 MB Flash, 4 MB PSRAM. PSRAM runs with 1.8 V, so GPIO12 must be floating or pulled high on boot. Works with low.js and/or other environments such as Arduino and ESP-IDF.
1x
7.00 USD
10x
5.25 USD (25 % off)
100x
3.50 USD (50 % off)
Over 280 in stock, shipment within 5 working days from Germany, EU
ESP32-WROVER 16 MB
Module with ESP32 microcontroller, 16 MB Flash, 8 MB PSRAM. PSRAM runs with 1.8 V, so GPIO12 must be floating or pulled high on boot. Works with low.js and/or other environments such as Arduino and ESP-IDF.
1x
8.00 USD
10x
6.40 USD (20 % off)
100x
5.60 USD (30 % off)
Over 10 in stock, shipment within 5 working days from Germany, EU
ESP32-WROVER-I 16 MB
Module with ESP32 microcontroller, 16 MB Flash, 8 MB PSRAM. PSRAM runs with 1.8 V, so GPIO12 must be floating or pulled high on boot. Works with low.js and/or other environments such as Arduino and ESP-IDF. PCB antenna disabled, with connector for IPEX antenna.
1x
8.00 USD
10x
6.40 USD (20 % off)
100x
5.60 USD (30 % off)
Over 10 in stock, shipment within 5 working days from Germany, EU
ESP32-WROVER-B 16 MB
Module with ESP32 microcontroller, 16 MB Flash, 8 MB PSRAM. PSRAM runs with 3.3 V, so GPIO12 must be floating or pulled low on boot. Works with low.js and/or other environments such as Arduino and ESP-IDF.
1x
8.00 USD
10x
6.40 USD (20 % off)
100x
5.60 USD (30 % off)
Over 10 in stock, shipment within 5 working days from Germany, EU
ESP32-WROVER-IB 16 MB
Module with ESP32 microcontroller, 16 MB Flash, 8 MB PSRAM. PSRAM runs with 3.3 V, so GPIO12 must be floating or pulled low on boot. Works with low.js and/or other environments such as Arduino and ESP-IDF. PCB antenna disabled, with connector for IPEX antenna.
1x
8.00 USD
10x
6.40 USD (20 % off)
100x
5.60 USD (30 % off)
Over 10 in stock, shipment within 5 working days from Germany, EU
External Wifi Antenna compatible to WROVER-I modules
These external Wifi antennas can be attached directly to the WROVER-I modules for best Wifi reception.
Cost: 
9.50 USD
Over 10 in stock, shipment within 5 working days from Germany, EU
ESP32-WROVER Breakout-Board
Tiny breakout board to use ESP32-WROVER on a breadboard. Soldering is possible by hand.
Cost: 
1.00 USD
Over 80 in stock, shipment within 5 working days from Germany, EU
Subtotal: 0.00 USD
Shipment costs and taxes are calculated in the next step based on the billing and shipment addresses.

IMPORTANT NOTICE!

The interactive parts of this page (Amounts, Checkout Button, etc.) do not work with disabled JavaScript!
You will not be able to complete a purchase with disabled JavaScript!
Please enable JavaScript or contact your system administrator in order to resolve this issue!
Alternatively you can email us at info@neonious.com to place your order.

IMPRINT

neonious GmbH
Münsterstr. 246
40470 Düsseldorf
Germany
Managing Director / CEO
Thomas Rogg
TEL+49 211 9241 8187
FAX+49 211 9241 8172